Oriental NC had previously been this unseen golden city that boaters would wistfully sigh over and preach the good works of the peerless marine services conducted here. It’s where anyone with major boat issues trudged their vessel to so the expert mechanics, riggers, glass workers (fiberglass), and electricians could work their magic. So when we arrived in Oriental, I could finally feel our goal, Bermuda, was within reach! Our rudder would be new our propeller would be fixed and our boat would be prepped for departure!
We chose SailCraft Marine Services, known for their fiberglass work as opposed to Deatons. The two rivals sit literally within throwing distance of each others travel lift.
Upon entering the SailCraft dock, Alan, the owner, showed us the layout, the bathrooms, amenities, the different offices and tool sheds, he introduced us to the employees, and other boats hauled out from our neck of the woods! Really above and beyond and we learned of the catastrophic boat overhauls they had completed. One man, came in days earlier with a keel partially torn off. Remember the Dismal Swamps we went down and my post on watching out for deadheads (= dislodged logs pinned to the bottom of the canal pointing upward)? Yeah, the boat hit a deadhead straight on and busted a hole in the boat. And if your curious, yes it was a fin keel.
So being on the hard, on the stilts, stuck on the dirt… it’s not fun. The marina backs you up into a slip where they lower two thick nylon slings and synch it snug around your 22,000 lb vessel and hope the sling is far back enough it doesn’t catch on your ruder, prop, or shaft but not too far back that the slings don’t capture the weight of the boat evenly. And then you watch as your 22,000 pound home is raised, above your head; OUT of the environment you’ve learned to keep your boat safe and protected. And then you watch as your baby is driven away by a complete stranger from you, it’s very emotional (*this end part was overdramatized by the author in case you’re not familiar with her*).
But really, Alan, was very professional and maneuvered the travel lift perfectly. He’s been around boats his entire life and it shows. He put us down on the block and put a few extra stilts under the hull than what we’re used to. I tell you, it’s like he was reading my mind! I know, I’m being paranoid but with prior yards, I always wished there were two or more stilts than what they provide. As someone who has slept on a boat on stilts… let me tell you, it can be REALLY unnerving when you first feel the boat move on land, so I was quite pleased to see this added comfort. Alan mentioned they do this for protection (but I knew better, he was a mind reader). He also kept the boat level on the blocks which was nice.
Now for the every day life. You walk up and down a ladder to get to your home, get a drill, forgotten power cord you name it. Every morning you wake up get dressed climb down the ladder then walk to go to the bathroom. Since the plumbing filters out into the yard gravel; I’m not a fan of brushing my teeth where I work. It’s not a far walk to the bathrooms thankfully but enough to make you skip your polite hellos to friends and power walk if you really have to “go”. Most people understand. When we did dishes, we carried the dishes in a tub down the ladder and past the docks. When we showered we climbed up and down the ladder with our shower bag and towel. And lastly, the little problem of having NO cell phone service and little to no internet.
I took a few pictures of our work in the yard seen below. We also varnished the bowsprit and toerail, rebedded the stanchion and inserted epoxy in the deck to reinforce soft balsa wood, install new aft cabin and kitchen lighting (led strips!), there was a bunch of parts ordered and one passport expedited. Thankfully, there was a car at the marina we were able to use to drive 30 minutes into a neighboring town for the nearest CVS for a passport photo.
Dust and woods bits will inevitably find there way into your bedroom sheets, kitchen and salon with any form of drilling or sanding. To unearth needed power tools, epoxies, varnish, sanders, and materials you need to tear through cabinets & mattresses to access storage units. All of this equates to a temporal work room war zone. I’m sure we’ve all been there whether it be moving, or buying a new house, it’s the first week of sleeping on a few cushions or camping gear. That was us for the past three weeks. But to be honest as sour of a situation I paint, I love the people, I love the stories, and honest to god I even love the work (Sometimes. As long as there’s a good podcast. and it’s sunny. with a beer. and beer koozie. and I have help…)
-
-
they say if you see rust colored water coming out of your rudder you need to replace it. Let me tell you another story, our story, of how that’s not the case
-
-
Start of our emergency emergency secondary backup steering. I hear repetition is good
-
-
Epoxy that casing. Thankfully the core was solid epoxy! No holes, no foam, no metal was hit in making this hole! Great work Pearson group
-
-
Main topping lift… needs a little TLC. The core is still intact…
-
-
Tape with electrical tape
-
-
Cut with a sharp knife
-
-
Lightly burn the edge until it starts to melt the sides.
-
-
Rebedded the mast collar
-
-
Taking out the old crummy lighting
-
-
Rebedding the aft hatch. We also took off the mid hatch completely and rebed that
-
-
Zincs 2 months old after traveling! Zincs should NOT look like this. This is what they might look like after 12 months. Clearly we have electrolysis problems to solve.
-
-
Max Prop. 4th time we’ve taken it apart
-
-
spinner casing
-
-
Bottom of the keel. Where I ran aground in Mamaroneck NY
-
-
Proof of the deadhead or snag we hit in the dismal swamp
-
-
and also for a good homemade lasagna
-
-
I live for receiving mail, it’s like Christmas